Skip to main content

Indie game storeFree gamesFun gamesHorror games
Game developmentAssetsComics
SalesBundles
Jobs
TagsGame Engines

Recent Prints made with Lego Tiles!

A topic by colony_nine created Oct 30, 2025 Views: 426 Replies: 8
Viewing posts 1 to 5
(+3)

Here are some recent print I've made with Lego tiles. If you want to learn more about printmaking with Lego, I have a free mini ebook on my page.

Cow in Field with Stars


(+2)

Very nice designs, lots of character. I too have been dabbling with some Lego printing, and i loved your zine: https://colony-nine.itch.io/a-somewhat-definitive-guide-to-lego-printing

I did some designs today actually. A lot smaller, with small ink pads and using the Lego more like a stamp. (though i have printed with Lego like you do with a roller printing inks).

(+1)

Really cool work! I see that you were able to get good registration from your prints. Any tips on getting the registration right? That is my biggest hurdle at the moment.

Ah, the eyes in the squid. Yes. That is actually a smaller stamp of its own, aligned by eye hovering over the printed squid. It’s easier because the stamp is quite small. I quite like the idea of doing some designs just with freely printed 2x2 or 4x4 stamps, but i haven’t really tried anything yet.

I have done prints with good registration, using pins. I’ll write a second post for that.

(+1)

So here is a piece with excellent registration. In fact it’s the same plate turned around and inked again with a 2nd colour. My typical setup for rolling-ink prints is shown in the “Hi” picture. I have an “L” (made from scrap kitchen floor lino) taped down that registers the bottom-left of the plate.

If you are prepared to have 2 ink plates out and 2 rollers, you can tape the top-edge of the paper to the board, print the first colour; lift the paper up (but leave taped); change the plate and ink it with the second colour; drop the paper back down, it should register on the 2nd plate in the same place. And i have done that. I use Cranfield Caligo Safe Wash which stays workable plenty long enough to do that, but with water-based inks, maybe not.

However, i also use Ternes Burton pins, you can see them taped down near the top of the image (the right-hand one is partially hidden under a plastic/bamboo brayer). They are described here: https://handprinted.co.uk/products/ternes-burton-registration-pins-plastic (they seem to be plastic now, not metal). Each paper you print is placed down and registered to the pins with 2 plastic tabs that you tape to the paper. You can then take the paper off the pins, do what you like (e.g. print another 9 of that plate, and then prepare a second plate and colour), and put the paper back on the pins in exactly the same place. All the paper you are printing has to have a pair of tabs, but you can in principle do 50-off 4-colour edition prints. It’s a bit fiddly and tedious, but the results are good. Wide margins help as i find that even my frogtape yellow masking tape tears the paper when removed.

Thinking about all this to write this post, made me think of a way using Lego itself, which i may get round to trying today. I’ll let you know.

P.S. carpet tape (double sided) is very useful for keeping the plate in place during inking and printing (though it bends a lot when you try and remove it). My favourite “baren” is a wooden spoon and a bit of “nose oil”.

(+1)

Thank you for the detailed response! I will definitely look into getting  some carpet tape and pins. I've told myself that I have to use up all my water based ink before I can invest in safe wash ink, but depending on where I can find it I might snag it during Black Friday sales.

(+1)

Hi, me again. So i tried my idea, which is basically to use Lego pieces to replace the Ternes Burton pins and tabs.

The long orange piece is taped down to my board and never moves.

Put a piece of paper down, attached two tabs (here each tab is made of two 2x4 flats: one red, and one grey) to the paper with tape. In the closeup, the nearer “tab” is not quite locked onto the orange plate, but when printing, it should be.

Now you can take the piece of paper away, and as long as you keep the Lego tabs taped to it, it should register perfectly when you reattach it to the orange plate.

So in principle this should work, it’s a bit more fiddly than Ternes Burton pins and tabs. But…

i haven’t tried printing, but i can tell straightaway that the orange piece wobbles too much and is not taped down well enough. Carpet tape would definitely be better, or possibly … (look away Lego fans) glue!

Maybe with your very large baseplates 48x48 you could add a long 2x12 piece directly onto that and then uses the 2x4 flats taped to the paper.

(+1)

Thank you for the alternative to the pins! I will test this idea out and see what happens. I might also see if I can get some scrap linoleum and try the pins, since I should have access to the pins and just need to get the carpet tape.